UHMWPE SEMI-PRODUCTS
Ultra-high molecular weight polyethylene( UHMWPE )is an outstanding engineering plastic.It? characterized by the following properties.

FEATURES：
(1)Very high abrasion resistance
(2)Very high impact strength
(3)Very low coefficient friction
(4)Good self-lubricant
(5)Excellent resistance to chemicals
(6)Good resistance to low temperature.
(7)Excellent dielectric properties

APPLICATIONS：
★Abrasion Resistance and Self-lubricant : marine fender, truck liners, gearing wheels, bearing bushes, sliding elements, chute liners, bunker liners, chain wear strip, guide strips and liners. paper and cardboard Industry, suction blades, foil blades, scraper and deflecting blades etc.
★Excellent Impact Strength : lug straps, picker stickers, loom pickers, picker shields and spinning etc.
★Hygienically : food processing, slide guide mechanisms, cutting boards, rammers, rolling pins, chopping blocks and moulds etc.
★High Resistance to Chemical Solvents: pump casings, seals, spray nozzles, agitator screws, acid pump impellers and valve liners, electroplating plating drums etc.


UHMWPE SHEET
Size 1030X2150mm ; 1200X2100mm ; 1000X3000mm
1500X3000mm ; 2000X3000mm ; 1000X4000mm
Thickness 6.5~180mm

UHMWPE PIPES
Size OD：32~630mm X ID：29~600mm
Wall thickness 3.0~57.2mm


UHMWPE FILM
Width (mm) 50,100~300
Length (meter/roll) 50~150 meter/roll
Thickness (mm) 0.050/0.075/0.1/0.15 /0.2/0.3/?~1.5
Tolerance <0.5 mm thickness ±0.02~0.03
0.5~1.0mm thickness ±0.05~0.06
1.0~1.5mm thickness ±0.1~0.15
UHMWPE BAR
Diameter (mm) 15 20 30 40
Roundness (mm) ≤3 ±1.5 ≤3 ±1.5 ≤3 ±1.5 ≤3 ±1.5
Length (mm) 1000 1000 1000 1000

Diameter (mm) 50 70 80 100
Roundness (mm) ≤5 ±2.5 ≤5 ±2.5 ≤5 ±2.5 ≤6 ±3
Length (mm) 1000 1000 1000 1000

Diameter (mm) 100 120 140 160
Roundness (mm) ≤6 ±3 ≤6 ±3 ≤6 ±3 ≤6 ±3
Length (mm) 1000 1000 1000 1000

Diameter (mm) 180 200 250 300
Roundness (mm) ≤6 ±3 ≤6 ±3 ≤6 ±3 ≤6 ±3
Length (mm) 150 150 150 150

Diameter (mm) 380 400 500 1000~2000
Roundness (mm) ≤6 ±3 ≤6 ±3 ≤6 ±3 ≤6 ±3
Length (mm) 150 150 150 150
Typical technical specification
Density 0.935~0.980 gram/m3
Hardness 60~68
Water adsorption <0.01%
Abrasion ratio 0.17
Friction coefficient 0.07~0.11
NOTCH impact strength 70 ~ 100 KJ/M2
IZOD Impact strength No break
Tensile strength 30~35 Mpa
Break elongation 200~300%
ANTISTATIC UHMWPE
Density 0.94~0.98g/cm3
Tensile strength 24 Mpa
Elongation 140%
Izod impact strength No break
Hardness 60~68
Coefficient of linear thermal expansion 1/K:2X10-4
Surface resistivity 104 ~109 Ω-cm

High Abrasion Resistance UHMWPE
Density 0.94~0.98g/cm3
Tensile strength 28 Mpa
Elongation 160%
Izod impact strength No break
Hardness 60~68
Coefficient of linear thermal expansion 1/K 2X10-4
Abrasion loss-(dry abrasion) 0.003 g/cm2

UHMWPE-FRAS HA
(Fire Retardant and Antistatic UHMWPE )
Density: GB1033 0.96~1.20 g/cm3
Crystalline Melting Range: 130 ~135 °C
Impact Strength at Yield:GB 1043 >70KJ/m2
Elongation at break: GB1040 >60%
Abrasion Index: g/cm2 GB/4085 0.011
Fire Behaviour: Oxygen Index:GB/2406 >28 %
Volume Resistivity: M Ohm GB/1410 5X 105
Molecular weight:(ASTM 4020-81) 3.0 Million min

Low Friction UHMWPE
Density 0.94~0.98g/cm3
Tensile strength 28 Mpa
Elongation 160%
Izod impact strength No break
dynamic Friction Coefficient 0.07~0.11